Hotline:+492590938950|
 
 
Servicehotline: +492590938950

Components

On request, Hagelschuer produces a range of components, which can also be directly installed and put into operation by competent specialist personnel. These include:

  • Water treatment/metering systems
  • Pressure reducing stations

  • Media distributors
  • Steam dryers

Hagelschuer also offers a comprehensive range of services, when it comes to support with reselling.

On request, our specialist personnel can also deliver, install and put these components into operation. We are naturally also happy to act as your partner when you, as a reseller, wish to procure components for steam boiler systems from experienced manufacturers or system constructors and require support.

High pressure / low pressure feed water tanks

Markus Karns Telephone: +49 (0) 25 90 - 9 38 95 - 228 karns@noSpam.dampfkessel.com
Michael Werner Telephone: +49 (0) 25 90 - 9 38 95 - 225 werner@noSpam.dampfkessel.com
Nicole Brandner Telephone: +49 (0) 25 90 - 9 38 95 - 309 brandner@noSpam.dampfkessel.com
Point of contact

NEW since 04/2019: Feed water modules

The design of the individual feedwater modules is basically the same. Each module consists of a steel profile construction with a screwed-on chequer plate base which is provided with a primer and top coat. All required components including the corresponding fittings are then installed.

All media lines and the necessary wiring work are pre-installed so that the module can be directly connected to the existing boiler plant after installation. This saves the need for complex interface coordination.

As a rule, the feedwater modules consist of the following basic components:

  • Feed water tank with trickle degasser including all fittings for heating, level control, etc.
  • Complete water treatment, generally with softening plant
  • Residual hardness control apparatus
  • Sampling cooler
  • Feed pump module incl. all fittings
  • Blow-down pressure reducer including cooling device
  • Independent electrical control – if this is not taken over by the boiler control system

 Further options are possible:

  • Condensate monitoring for turbidity or conductivity
  • Desalination heat exchangers
  • Vapour heat exchanger
  • 2nd dosing unit
  • UO plant with permeate reservoir
  • Water meter for raw water, soft water or permeate
  • And much more...

Contact us, we will be happy to advise you!

Example of a feed water module
Michael Werner Telephone: +49 (0) 25 90 - 9 38 95 - 225 werner@noSpam.dampfkessel.com
Helmut Haubenwallner Telephone: +49 (0) 25 90 - 9 38 95 - 329 haubenwallner@noSpam.dampfkessel.com
Point of contact

Blow-down pressure reducers

Variants for multiple boiler systems can naturally also be manufactured and supplied.

On request, cooling coils can be integrated in the blow-down tank for energy recovery from the waste water quantity.

  • Upright blow-down pressure reducers
  • Upright blow-down pressure reducers (stainless steel)
Markus Karns Telephone: +49 (0) 25 90 - 9 38 95 - 228 karns@noSpam.dampfkessel.com
Nicole Brandner Telephone: +49 (0) 25 90 - 9 38 95 - 309 brandner@noSpam.dampfkessel.com
Point of contact

Condensate lifting units / pressure reducers

Condensate return systems produced from black steel or full stainless steel; unpressurised – low pressure or high pressure for collecting and returning unpressurised or boiling hot condensate, with or without condensate pumps, generally including level technology and complete fittings equipment – we supply every variant you may require.

On request we offer you competent, on-site consultancy. Due to the many systems already brought to market, we already have a range of standard units available for you. If required, we can naturally also supply these tanks to you as complete modules with tailored equipment.

Markus Karns Telephone: +49 (0) 25 90 - 9 38 95 - 228 karns@noSpam.dampfkessel.com
Nicole Brandner Telephone: +49 (0) 25 90 - 9 38 95 - 309 brandner@noSpam.dampfkessel.com
Point of contact

Steam pressure reducing stations

Modular steam pressure reducing stations have many advantages. Not only can they be delivered quickly –standard versions within three days, special solutions within a week – but they also enable a more flexible utilisation of the steam boiler plant, with significantly shorter installation times. The new modular pressure reducing lines, which are fully equipped with control components, can also be retrofitted into existing steam boiler systems.

The control units consist of: manometer set, shut-off, dirt trap, cyclone steam dryer with drainage, mechanical pressure reducing valve and safety valve. They are delivered ready for connection and mounted on a stand construction.

Three different types are available from stock.

  • Steam pressure reduction station for 500 kg/h
  • Steam pressure reduction station for 1,000 kg/h
  • Steam pressure reduction station for 2,000 kg/h

You can find the pressure reduction stations here, in our webshop!

[Translate to English:] Beispielhafte Zeichnung einer Druckminderstrecke.

Water treatment / metering

On request, our specialist personnel can also deliver, install and put these components into operation. We are naturally also happy to act as your partner when you, as a reseller, wish to procure components for steam boiler systems from experienced manufacturers or system constructors and require support.

  • Water treatment with residual hardness testing
  • Reverse Osmosis System
Markus Karns Telephone: +49 (0) 25 90 - 9 38 95 - 228 karns@noSpam.dampfkessel.com
Point of contact

Distributors for steam, condensate and other media

We produce the distributors and collectors required by you for all media, including drainage systems and fittings, shut-off valves - also motor or pneumatically driven.

As a specialist according to HP0 with module A1 in accordance with the pressure vessel directive, we supply you with all distributors / collectors with the corresponding pre-testing and documentation.

Markus Karns Telephone: +49 (0) 25 90 - 9 38 95 - 228 karns@noSpam.dampfkessel.com
Nicole Brandner Telephone: +49 (0) 25 90 - 9 38 95 - 309 brandner@noSpam.dampfkessel.com
Point of contact

Condensate monitoring systems

Condensate monitoring systems - generally for conductivity or turbidity: We are happy to supply you with these fully pre-assembled as modules including a corresponding control unit and according to your requirements with a valve for draining "poor" / contaminated condensate. We shall be delighted to advise you on the selection of the right system or provide you with support through communication with your expert assessors.

Markus Karns Telephone: +49 (0) 25 90 - 9 38 95 - 228 karns@noSpam.dampfkessel.com
Point of contact

Steam dryers

Steam dryers - for a wide range of applications with a new installation, or alternatively for retrofitting in problem cases - we supply you with steam dryers in a wide range of materials for improving the steam quality with all the requisite fittings, with all permissible operating pressures and with variable union positions. We naturally also maintain a range of standard parts here. However, if the respective installation situation does not permit the use of a standard component then we can also offer you an individual solution here.

Markus Karns Telephone: +49 (0) 25 90 - 9 38 95 - 228 karns@noSpam.dampfkessel.com
Nicole Brandner Telephone: +49 (0) 25 90 - 9 38 95 - 309 brandner@noSpam.dampfkessel.com
Point of contact

Steam accumulators - in horizontal or vertical format

Installation of a steam accumulator at the customer's site, not yet insulated
Steam accumulator at the customer's site, insulated and connected
Michael Werner Telephone: +49 (0) 25 90 - 9 38 95 - 225 werner@noSpam.dampfkessel.com
Georg Hagelschuer Telephone: +49 (0) 25 90 - 9 38 95 - 0 g.hagelschuer@noSpam.dampfkessel.com
Point of contact

Heat exchanger stations

The modules are designed for a steam inlet pressure of 2.5 to 13 bar with an output of 200 to 1,000 KW up to max. 100 °C flow temperature. The heat exchanger stations are another important component in the Hagelschuer modular series. They allow a broader utilisation of the steam boiler plant and savings in

building and energy technology. The advantages of the modular design are obvious; the heat exchanger modules are suitable for retrofitting in existing plants, easy to assemble and quick to procure due to extremely short delivery times.

The following standard versions are available as assemblies via our webshop:

  • Heat exchanger station for 200 KW

  • Heat exchanger station for 400 KW

  • Heat exchanger station for 600 KW

  • Heat exchanger station for 800 KW

  • Heat exchanger station for 1000 KW

Click here to go straight to the heat exchanger stations in our webshop!

Heat exchanger stations
© Georg Hagelschuer GmbH & Co. KG | Gewerbestraße 60 | D-48249 Dülmen | Germany